Crown CTs 600 Power Amplifier

Crown CTs 600 Power Amplifier

Crown’s CTs Series amplifiers provide exceptional performance, flexibility and value for installed sound applications. CTs Series amplifiers feature independent selection of high and low impedance operation for a specific channel, plus power levels and features that were carefully chosen to match the requirements of fixed install design. Easy integration with HiQnet™ and CobraNet™ allows CTs amplifiers to deliver a comprehensive lineup of monitoring and control features along with digital audio transport for an award-winning digital audio solution.

High power density. All two channel models and four channel model in a 2RU chassis, eight channel model in a 3RU chassis Crown Switching Power Supply for lighter weight Selectable "Constant-Voltage" or low-impedance (4/8 ohm) operation per channel on 2-channel models, and per channel-pair on 4-and 8-channel models 100V direct outputs on CTs 2000, CTs 3000, CTs 4200, and CTs 8200 Legendary Crown class-I (BCA) and AB+B output topologies offer the best in amplifier reliability 4- and 8-channel models offer perfect independent power solutions for multi-zoned systems· "FIT" (Fault Isolation Topology) circuitry on 4- and 8-channel models isolates fault conditions without affecting neighboring channels Comprehensive array of indicators provide accurate diagnostics Two-channel models are fully PIP2-compatible. Multi-channel models accept MC accessory modules.

Minimum Guaranteed Power

20 Hz - 20 kHz) CTs 600

2-ohm Dual (per ch.) 150W

4-ohm Dual (per ch.) 300W

8-ohm Dual (per ch.) 300W

16-ohm Dual (per ch.) 300W

70V Dual (per ch.) 300W

100V Dual (per ch.) 300W* 6

4-ohm Bridge 300W

8-ohm Bridge 600W

16-ohm Bridge 600W

100V Bridge 600W

140V Bridge 600W

200V Bridge 600W*

Performance:

Frequency Response (at 1 watt, 20 Hz - 20 kHz) ± 0.25 dB

Signal to Noise Ratio (ref. rated power, 20 Hz to 20 kHz, A-weighted) < 105 dB

Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz < 0.1%

Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from –40 dB to full rated power < 0.1%

Damping Factor: 10 Hz to 100 Hz > 3000

Crosstalk (below rated power) 20 Hz to 1kHz > 80 dB

Common Mode Rejection (CMR) (20 Hz to 1 kHz, typical) 50 dB

DC Output Offset < 2 mV

Input Impedance nominally balanced, nominally unbalanced 10 k ohms,5 k ohms

Maximum Input Level

Before input compression +20 dBu Absolute maximum + 32 dBu

Load Impedance (Note: Safe with all types of loads) Stereo 2, 4, 8, 16 ohms, Bridge Mono 70V, and 100V* 4, 8, 16, 100V*, 140V and 200V*

Voltage Gain (at maximum level setting) 8/4 Ohm Operation 35:1 (31 dB) 26 dB 20:1 (26 dB) 70V Operation 50:1 (34 dB) 100V Operation n/a

Input Sensitivity = 1.4V 2/4/8 ohms = 1.4V 70V = n/a 100 V = 4 ohm: 1.74V. 26 dB gain = 8 ohm: 2.46V

Required AC Mains (+15%, – 25%) 120V/60 Hz, 230V/50 Hz

Power Draw at Idle (120 VAC mains) 24W (Standby Mode)

Overall Group Delay < 120 usec

Cooling Continuously variable speed forced air, front-to-back airflow

Dimensions Width 19 in. (48.3 cm.) Height 3.5 in. (8.9 cm.) Depth 14.25 in. (36.2 cm.)

Net Weight 22.8 lb (10.3 kg),

Shipping Weight 27.7 lb (12.6 kg)